Ford Instrument Cluster Wiring Diagram
Joined
·
2,000 Posts
Discussion Starter · #1 ·
For an 03 E-350 and a late 99 F-250? I am wondering if I can repin my van to use the f cluster and have a factory tach. I think the tach wire is there, just not connected to anything.
Joined
·
6,479 Posts
Ive got all that stuff just not in a format I can post in here.
Joined
·
2,000 Posts
Discussion Starter · #3 ·
Joined
·
2,000 Posts
Discussion Starter · #4 ·
Anybody have these? I could REALLY use them! I thought I could do it without them...... Thanks!!
Joined
·
6,479 Posts
Joined
·
2,000 Posts
Discussion Starter · #6 ·
Thanks Crowz!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Joined
·
6,479 Posts
Your welcome 
Joined
·
553 Posts
any way to get a smiliar pinout for the overhead console on a 99.5 vs an 02...i have it installed but the connectors behind the rh kick panel were different..
Joined
·
6,479 Posts
I can pull the overhead diagrams for a 2002 but I cant get the 99 stuff to load.
Joined
·
2,000 Posts
Discussion Starter · #10 ·
Crowz-where are those diagrams from? I just bought a one year subscription to alldata for an 01 f 250. What a clusterf**ck trying to read that.
Joined
·
290 Posts
IIRC its a pink/white for the tach. Its has a tag from
oem marked CTO. It brakes out of the harness to the left of the
brake booster.
Did this years ago. F-cluster in a E.
Bill
Joined
·
6,479 Posts
Crowz-where are those diagrams from? I just bought a one year subscription to alldata for an 01 f 250. What a clusterf**ck trying to read that.
Now you see what Im fighting to get that stuff out for you
Its under diagrams then connector views and then instrument cluster.
Joined
·
2,000 Posts
Discussion Starter · #13 ·
IIRC its a pink/white for the tach. Its has a tag from
oem marked CTO. It brakes out of the harness to the left of the
brake booster.Did this years ago. F-cluster in a E.
Bill
Where do you think I got the idea??
Now you see what Im fighting to get that stuff out for you
Its under diagrams then connector views and then instrument cluster.
Yep, found it thanks. I will scan and post them when I get a chance. Fever, I will do your overhead console as well.
After getting the connector pinouts this morning, I was able to get a lot of it working after work. The tach works!! I think the speedo works, it did move going up the driveway. Fuel gauge reads full, and it is full, so hopefully that is good. The only thing I know for sure isn't working is the voltmeter. Not sure about coolant temp, didn't let it run long enough.
But now my van has 550,000 miles. Bill, is it hard to put my 170,000 odometer in there? I would imagine I can't just roll this one back somehow.
Joined
·
2,000 Posts
Discussion Starter · #14 ·
Fever-here is the pinout for an 01 overhead console
Joined
·
553 Posts
Joined
·
2,000 Posts
Discussion Starter · #16 ·
Everything is working except the voltmeter and coolant temp. How can I force the coolant gauge to move to see if it even works, assuming it is hooked up properly. The connector at the sensor has a signal and ground.
Joined
·
1 Posts
Hello All,
I know this is an old thread but I am looking for the Instrument cluster pinouts (Black & Blue Plug 26 pin) for a 2006 Ford F250 Super Duty Truck so I can power it up on the bench. Can someone help me please with that?
Source: https://www.powerstrokenation.com/threads/anybody-have-gauge-cluster-wiring-diagrams.26680/
Posted by: specialistlights.blogspot.com